All Products
Contact Person :
lei
Phone Number :
13266828705
Keywords [ linear low density polyethylene granules ] match 12 products.
Bio Based Sugarcane LLDPE Linear Low Density Polyethylene Granules Braskem LH0820/30AF
| Density (23°C): | 0.918 G/cm³ |
|---|---|
| Melt Mass-Flow Rate (MFR) (190°C/2.16 Kg): | 0.8 G/10 Min |
| Processing Method: | Blown Film ,Film Extrusion |
Braskem Green PE SLH118/21 LLDPE Material Bio Based Sugarcane Polyethylene Granules
| Density (23°C): | 0.918 G/cm³ |
|---|---|
| Melt Mass-Flow Rate (MFR) (190°C/2.16 Kg): | 1 G/10 Min |
| Processing Method: | Blown Film Extrusion. |
Bio Based Polyethylene Sugarcane LLDPE Granules Braskem Green PE SLH118
| Density (23°C): | 0.916 G/cm³ |
|---|---|
| Melt Mass-Flow Rate (MFR) (190°C/2.16 Kg): | 1 G/10 Min |
| Processing Method: | Blown Film Extrusion. |
Braskem Green PE SLL118 Bio Based Sugarcane Polyethylene LLDPE Plastic Granules
| Density (23°C): | 0.916 G/cm³ |
|---|---|
| Melt Mass-Flow Rate (MFR) (190°C/2.16 Kg): | 1 G/10 Min |
| Processing Method: | Blown Film Extrusion. |
Polyethylene LLDPE Granules Bio Based Sugarcane Braskem Green PE SLL318
| Density (23°C): | 0.918 G/cm³ |
|---|---|
| Melt Mass-Flow Rate (MFR) (190°C/2.16 Kg): | 2.7 G/10 Min |
| Molding Temperature: | 170 -180 °C |
HANWHA 3120 Hanwha Chemical LLDPE
| Density: | 0.920 G/cm³ |
|---|---|
| Melt Mass-Flow Rate (MFR) (190°C/2.16 Kg): | 1.0 G/10 Min |
| Melt Temperature: | 150 To 190 °C |
Petrothene® Ga50224 LyondellBasell LLDPE
| Density (23°C): | 0.918 G/cm³ |
|---|---|
| Melt Mass-Flow Rate (MFR) (190°C/2.16 Kg): | 2 G/10 Min |
| Processing Method: | Blown Film Cast Film Film Extrusion |
Petrothene® GA502023 LyondellBasell LLDPE
| Density (23°C): | 0.918 G/cm³ |
|---|---|
| Melt Mass-Flow Rate (MFR) (190°C/2.16 Kg): | 2 G/10 Min |
| Processing Method: | Blown Film Cast Film Film Extrusion |
Petrothene GA502022 LyondellBasell LLDPE
| Density (23°C): | 0.918 G/cm³ |
|---|---|
| Melt Mass-Flow Rate (MFR) (190°C/2.16 Kg): | 2 G/10 Min |
| Processing Method: | Blown Film Cast Film Film Extrusion |
Prime Polymer Evolue Sp1520 Blown Film
| Melt Mass-Flow Rate (MFR): | 2 G/10 Min |
|---|---|
| Density: | 0.919 G/cm³ |
| Durometer Hardness (Shore D, Injection Molded): | 54 |